Oneplus 12 spare parts

Technical Characteristics of OnePlus 12 Replacement Parts

The following are the technical specifications of the various replacement parts available for the OnePlus 12:

1. Screen Display

• Type: Fluid AMOLED
• Size: 6.7 inches
• Resolution: 1440 x 3200 pixels
• Protection: Corning Gorilla Glass Victus
• Refresh Rate: 120Hz

2. Battery

• Type: Li-Po
• Capacity: 5000 mAh
• Fast Charging: 65W

3. Camera Module

• Primary Sensor: 50 MP, f/1.9
• Ultrawide Sensor: 48 MP, f/2.2
• Telephoto Sensor: 8 MP, f/2.4

4. Charging Port

• Type: USB Type-C 3.1

5. Back Cover

• Material: Glass
• Features: Frosted finish, Anti-smudge coating

Instructions for Replacing OnePlus 12 Replacement Parts

Follow these detailed instructions to replace various parts of the OnePlus 12.

1. Screen Display Replacement

• Power off your OnePlus 12 and remove the SIM card tray.
• Use a heat gun to soften the adhesive around the edges of the back cover.
• Insert a plastic pry tool between the back cover and the frame, gently pry the cover off.
• Remove the screws securing the inner plastic cover and disconnect the battery.
• Detach the display connector from the motherboard.
• Heat the edges of the damaged screen to soften the adhesive, and carefully remove it.
• Clean the frame to remove any adhesive residue.
• Apply new adhesive to the frame and place the new screen display, ensuring it aligns properly.
• Reconnect the display connector to the motherboard.
• Reconnect the battery and replace the inner plastic cover and screws.
• Snap the back cover back in place or apply new adhesive if needed. Power on the device to test the new screen.

2. Battery Replacement

• Power off your device and remove the SIM card tray.
• Use a heat gun to soften the adhesive on the back cover.
• Insert a plastic pry tool to remove the back cover safely.
• Remove screws from the internal protective cover and disconnect the battery from the motherboard.
• Use a pull tab or pry tool to carefully lift and remove the old battery.
• Place the new battery into the slot and reconnect it to the motherboard.
• Replace the internal protective cover and screws.
• Snap the back cover back in place or use new adhesive. Power on the device to ensure the battery is functioning correctly.

3. Camera Module Replacement

• Power off your device and remove the SIM card tray.
• Heat and pry off the back cover using a heat gun and plastic pry tool.
• Remove the screws from the internal protective cover and disconnect the battery.
• Locate the camera module and disconnect it from the motherboard.
• Carefully remove the old camera module from its slot.
• Install the new camera module into the slot and reconnect it to the motherboard.
• Reconnect the battery and replace the internal protective cover and screws.
• Reattach the back cover, using new adhesive if necessary. Power on the device and test the new camera module.

4. Charging Port Replacement

• Power off your device and remove the SIM card tray.
• Apply heat to the back cover edges and use a plastic pry tool to remove it.
• Remove the internal cover screws and disconnect the battery.
• Disconnect the charging port flex cable from the motherboard.
• Unscrew and remove the old charging port from the chassis.
• Install the new charging port and secure it with screws.
• Reconnect the charging port flex cable to the motherboard.
• Reconnect the battery and replace the internal cover and screws.
• Reattach the back cover and power on the device to verify the new charging port is working.

5. Back Cover Replacement

• Power off the device and remove the SIM card tray.
• Heat the edges of the back cover with a heat gun to soften the adhesive.
• Use a plastic pry tool to gently lift and remove the old back cover.
• Clean the edges to remove any leftover adhesive.
• Align and place the new back cover, ensuring it properly fits.
• Apply gentle pressure to secure the new back cover in place.
• Power on the device to ensure it functions correctly with the new back cover.