Oppo Reno 4 Pro 5G spare parts

Technical Characteristics of Oppo Reno 4 Pro 5G Repuestos

Oppo Reno 4 Pro 5G is a high-end smartphone that features several replaceable parts (repuestos). Below are the key technical characteristics of some commonly replaced parts:

Display

• Type: Super AMOLED capacitive touchscreen
• Size: 6.5 inches
• Resolution: 1080 x 2400 pixels
• Protection: Corning Gorilla Glass 5
• Refresh Rate: 90Hz

Battery

• Type: Non-removable Li-Po
• Capacity: 4000 mAh
• Fast Charging: 65W SuperVOOC 2.0

Camera Module

• Main Camera: Quad setup - 48 MP, 8 MP (ultrawide), 2 MP (macro), 2 MP (depth)
• Front Camera: 32 MP

Motherboard

• Chipset: Qualcomm SM7250 Snapdragon 765G
• CPU: Octa-core (1x2.4 GHz Kryo 475 Prime, 1x2.2 GHz Kryo 475 Gold, 6x1.8 GHz Kryo 475 Silver)
• GPU: Adreno 620

Instructions on How to Replace Oppo Reno 4 Pro 5G Repuestos

Tools Required

• Phillips #000 screwdriver
• Plastic prying tools
• Suction cup
• SIM card ejector tool
• Adhesive strips (optional)
• Heat gun or hairdryer (for display replacement)

Steps to Replace the Display

Warning: Replacing the display may void the warranty. Proceed with caution and ensure the phone is powered off before starting.

1. Use the SIM card ejector tool to remove the SIM tray.
2. Apply a gentle heat to the edges of the phone using a heat gun or hairdryer to soften the adhesive securing the back cover.
3. Carefully insert a plastic prying tool between the back cover and frame. Gently pry around the edges to release the back cover.
4. Remove the screws securing the metal shield covering the battery and motherboard using the Phillips #000 screwdriver.
5. Disconnect the battery connector first to avoid short circuits.
6. Disconnect the display cable and other necessary connectors from the motherboard.
7. Gently apply heat to the front screen to loosen the adhesive securing the old display.
8. Use the suction cup to lift the old display while carefully prying around the edges to remove it completely.
9. Remove any remaining adhesive residue from the frame before installing the new display.
10. Place the new display onto the frame and gently press it down to secure it with the adhesive.
11. Reconnect the display cable, battery connector, and other necessary connectors to the motherboard.
12. Reattach the metal shield and tighten the screws.
13. Snap the back cover back onto the phone and ensure it is properly aligned and sealed.
14. Reinsert the SIM tray.
15. Power on the phone to perform a test, ensuring the new display is functioning correctly.

Steps to Replace the Battery

Warning: Replacing the battery yourself may void the warranty. Ensure the phone is powered off before starting the replacement.

1. Use the SIM card ejector tool to remove the SIM tray.
2. Apply gentle heat to the back cover edges using a heat gun or hairdryer to soften the adhesive.
3. Insert a plastic prying tool between the back cover and frame and gently pry around to remove the back cover.
4. Remove the screws securing the metal shield over the battery using a Phillips #000 screwdriver.
5. Disconnect the battery connector from the motherboard.
6. Slowly peel off the adhesive strips holding the battery in place. If necessary, use a prying tool to lift the battery carefully.
7. Insert the new battery, making sure it is properly seated and aligned.
8. Reconnect the battery connector to the motherboard.
9. Reattach the metal shield and tighten the screws.
10. Snap the back cover back onto the phone, ensuring it is securely in place.
11. Reinsert the SIM tray.
12. Power on the phone to verify the new battery is functioning correctly.

For other repuestos such as the camera module or motherboard, similar steps involving careful removal of the back cover, disconnecting relevant connectors, and ensuring all components are seated properly apply. Always ensure to follow proper procedures and precautions to avoid damaging the phone.