Oukitel K8000 spare parts

Technical Characteristics of Oukitel K8000 Repuestos

The Oukitel K8000 is a robust smartphone known for its large battery capacity. Below are the technical characteristics of the Oukitel K8000 repuestos (replacement parts):

Battery

• Type: Li-Ion
• Capacity: 8000 mAh
• Voltage: 3.85V
• Charging Time: Approximately 5 hours

Screen

• Size: 5.5 inches
• Resolution: 720 x 1280 pixels
• Type: AMOLED
• Protection: Corning Gorilla Glass

Camera

• Rear Camera: 16 MP + 2 MP
• Front Camera: 13 MP
• Features: LED flash, HDR, panorama

Other Components

• Battery Connector: Compatible with original K8000 battery
• Charging Port: Micro-USB
• Audio Jack: 3.5mm standard port
• SIM Tray: Dual SIM (Nano-SIM, dual stand-by)

Instructions to Replace Oukitel K8000 Repuestos

Below are detailed instructions for replacing various components of the Oukitel K8000:

Replacing the Battery

• Turn off the device and remove any SIM cards or memory cards.
• Use a small Phillips screwdriver to remove the screws at the bottom of the phone.
• Gently insert a plastic pry tool between the back cover and the phone frame to release the clips holding the back cover in place. Carefully detach the back cover.
• Locate the battery connector and use the pry tool to carefully disconnect it from the motherboard.
• Lift and remove the old battery from the phone. If the battery has adhesive strips, use the pull tabs to gently remove it.
• Insert the new battery into the battery compartment and connect the battery connector to the motherboard.
• Reattach the back cover by pressing it firmly until all clips are secure, then replace the screws at the bottom of the phone.

Replacing the Screen

• Turn off the device and remove any SIM cards or memory cards.
• Remove the back cover and disconnect the battery as explained in the battery replacement instructions.
• Use the Phillips screwdriver to remove any screws securing the motherboard and screen components.
• Detach the ribbon cables connecting the screen to the motherboard using a plastic pry tool.
• Gently heat the edges of the screen with a heat gun or hairdryer to soften the adhesive.
• Use the pry tool to carefully lift and remove the screen from the frame.
• Place the new screen in the frame and reattach the ribbon cables to the motherboard.
• Secure the motherboard and other components with the removed screws.
• Reconnect the battery, reattach the back cover, and secure it with the screws at the bottom of the phone.

Replacing the Charging Port

• Turn off the device and remove any SIM cards or memory cards.
• Follow the steps to remove the back cover and disconnect the battery as described in the battery replacement instructions.
• Use the Phillips screwdriver to remove the screws securing the motherboard and charging port components.
• Carefully disconnect any ribbon cables or connectors attached to the charging port module.
• Use a pry tool to lift and remove the defective charging port from its slot.
• Place the new charging port module into the slot and reconnect any ribbon cables or connectors.
• Secure the charging port module and motherboard with the screws you removed earlier.
• Reconnect the battery, reattach the back cover, and securely fasten it with the screws at the bottom of the phone.

Replacing the Camera Module

• Turn off the device and remove any SIM cards or memory cards.
• Remove the back cover and disconnect the battery as previously explained.
• Use the Phillips screwdriver to remove screws securing the camera module to the phone.
• Carefully disconnect any ribbon cables or connectors attached to the camera module.
• Gently lift and remove the defective camera module using a pry tool.
• Place the new camera module into its slot and reconnect any ribbon cables or connectors.
• Secure the camera module with the screws you removed earlier.
• Reconnect the battery, reattach the back cover, and securely fasten it with the screws at the bottom of the phone.